Both is used to rate limit traffic on a interface or sub-interface to adhere to a traffic contract or to restrict further congestion of traffic down to the remaining network devices. Shaping and Policing is a Traffic Condition Technique comes under QoS PHB. 1 Introduction to Virtual Extensible LAN (VXLAN).Wordpress Admin Case Study Segment Routing 1 Introduction to Ethernet Virtual Private Network (EVPN).Tags affinity bit affinity mask attribute flag mpls te 1 Attribute Flag & Affinity Bit – MPLS Traffic EngineeringĪnjan Chandra Case Study Traffic Engineering.Tags hub & spoke HUB & SPOKE MPLS VPN hub spoke mpls mpls Tags CEF fast-switching Packet-Forwarding process-switching Data Plane is the Hardware Module which perform the data transfer(forwarding of packet).
Eve ng vs gns3 software#
Control Place the the logical unit of the hardware which perform the software operation like routing protocol(ospf, bgp, ldp etc.).
![eve ng vs gns3 eve ng vs gns3](https://www.expertnetworkconsultant.com/wp-content/uploads/2020/12/Configure-Cisco-ASAv-on-GNS3-for-Hands-on-CCNP-Labs.png)
![eve ng vs gns3 eve ng vs gns3](https://i0.wp.com/ipwithease.com/wp-content/uploads/2020/02/GNS3-VS-PACKET-TRACER-TABLE.jpg)
1 Packet Switching – Routing and ForwardingĪ network device consist of three logical unit, Control Place, Data Plane and Management Plane.Tags add path additional path bgp pic multipath Tags BGP Distance bgp-path-selection iBGP over EBGP prefer iBGP over EBGP If the rote is locally originated then it will prefer ibgp path, otherwise it will chose ebgp path. In a situation where a route coming from both ebgp and ibgp peer, the best path election will takes place in two different way. Tags bgp-pa bgp-path-attribute bgp-path-selection path-attribute The second Round is Selection where BGP Best… The first round is Rejection where any route matching certain condition will be rejected. There are 3 (Rejection, Selection, Tie-Break) rounds of BGP Path Selection which involve 18 different steps. In this discussion we will dive into the BGP Path Selection Algorithm. Tags bgp-fsm bgp-input-events bgp-message-types bgp-stuck-in-active BGP is a Transport Layer Protocol, hence TCP provides fragmentation, acknowledgement, sequencing… Before establishing BGP Peer Connection, two neighbor must perform TCP Three-Way-Handshake and open a connection to Port number 179.
![eve ng vs gns3 eve ng vs gns3](https://i.imgur.com/X7WicXE.png)
In this tutorial we will discuss about different message types of BGP, BGP Peer Connection, BGP Finite State Machine. Tags bgp bgp-fsm bgp-stuck-in-active bgp-stuck-in-idle Refer the below flow chart where it explains… It's a Cisco proprietary and use to enable fast DR recovery in a multi-access network.īGP Neighbor States – IDLE – CONNECT – ACTIVE From this explanation we might understand that a BGP process remains in ACTIVE state is due to TRANSPORT ERROR means the BGP process is unable to initiate a TCP Connection to the Neighbor. Remembering old DR is an optimization of DR/BDR election process. Introduction - Preemption vs Remember OLD DR. Tags backup area isolated area multiarea adjacency ospf partitioned area Tags external loop prevention inter area loop prevention ospf loop prevention Tags external-lsa forwarding-address ospf Tags N/P Bit nssa nssa-area ospf p-bit Propagate Bit Its is called propagate bit, when set to 0(zero/Unset), NSSA ABR doesn't translate the Type-7 to Type-5, otherwise the NSSA ABR translate the Tyep-7 to Type-5 Tags dhcp dhcp ack dhcp discover dhcp lease dhcp offer dhcp reuest dhcp transaction id dhcpdecline dhcpinform dhcpnak dhcprelease doraĪ NSSA ABR Translate Type-7 LAS to Type-5 LSA based on the value of P-Bit. Clients/Hosts send request to DHCP servers… DHCP essentially uses BOOTP message format added with some options filed using UDP(Port 67 & 68). It is an extension of BOOTP protocol and backward compatibility is maintained.